We’ve been also concentrating on bettering the things management and QC method in order that we could continue to keep terrific benefit inside the fiercely-competitive company for Low MOQ for Tmz Astm B387 Molybdenum Sheet Forming For Heat Shield, If you are fascinated in almost any of our solutions or would want to discuss a custom-made order, remember to really feel absolutely free to contact us.
We’ve been also concentrating on bettering the things management and QC method in order that we could continue to keep terrific benefit inside the fiercely-competitive company for Astm B387 Molybdenum Sheet Forming, Molybdenum Sheet Forming For Heat Shield, Tmz Molybdenum Sheet Forming, We have been eager to cooperate with foreign companies which care much on the real quality, stable supply, strong capability and good service. We can give the most competitive price with high quality,because we are much MORE Expert. You are welcomed to visit our company at any time.
Molybdenum Sheet
1.Thickness and width tolerances
Cold rolled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 0.10 | 0.008 | 305 | 0.5 |
| 0.10-0.127 | 0.010 | 305 | 0.5 |
| 0.127-0.15 | 0.010 | 610 | 0.5 |
| 0.15-0.25 | 0.015 | 800 | 0.5 |
| 0.25-0.50 | 0.020 | 915 | 1.6 |
| 0.50-0.80 | 0.028 | 915 | 1.6 |
| 0.80-1.20 | 0.035 | 915 | 1.6 |
| 1.20-2.00 | 3% | 915 | 1.6 |
Cold rooled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 1.00 | 0.080 | 850 | 2.0 |
| 1.00-1.50 | 0.130 | 850 | 2.0 |
| 1.50-2.00 | 0.150 | 850 | 2.0 |
| 2.00-3.60 | 0.180 | 1200 | 2.0 |
| 3.60-50.00 | 5% | 1500 | 2.0 |
Length tolerace:
The length tolerace for sheet length up to 2500 mm is max. +5/-0 mm.
The length tolerance of sheet cuts can vary with a total tolerance range not exceeding the above given value. The maximum sheet dimensions depend on the sheet thickness.other dimensions upon request.
Sheet with premium surface condition are available from 0.15 to 1 mm.Sheet with thickness from 0.127 to 0.381 mm can be delivered as coils upon request.(production length max.10500mm)
Flatness:
Max.1% for sheet thickness≥0.3mm
Max.4% for sheet thickness＜0.3mm
(measuring proedure on the basis of ASTM B386)
2. Physical and mechanical product properties.
Density: ≥10.2g/cm³
Vickers Hardness:
≤1.0mm: 240-280 HV
1.00-3.60mm: 240-270 HV
306-10.00mm: 220-270 HV
10.00-50.00: ＞200 HV
Tensile test:
| Thickness(mm) | Tensile Srenght Min. (MPa) | 0.2 % Yield strength Min. (MPa) | ElongationMin.(%) |
| 0.1-0.25 | 700 | 620 | 2.0 |
| 0.25-0.40 | 680 | 590 | 3.0 |
| 0.40-0.65 | 680 | 590 | 5.0 |
| 0.65-1.50 | 680 | 580 | 10.0 |
| 1.50-2.30 | 640 | 580 | 12.0 |
| 2.30-5.00 | 640 | 580 | 15.0 |
| 5.00-10.00 | 640 | 580 | 10.0 |
| 10.00-13.00 | 590 | 540 | 10.0 |
| 13.00-25.00 | 500 | 480 | 2.0 |
| 25.00-50.00 | 500 | 480 | 1.0 |
Surface condition
Appearance: The material will be of uniform quality, free from foreign matter, splits and fractures. bed sheet(not trimmed) may have small edge cracks.
Surface defects are assessed in the frame of visual inspection.
Local surface defects can be removed by frinding within the specified thickness tolerace.
Surface condition: Cold rolled, bright(≤1mm) Ra≤0.20μm
Cold rolled, pickled: Ra≤1.00μm
Cold rolled ground: Ra≤0.60μm
Chemical composition:
| Main and minor components | Min.content(%) | ASTM B386 (361) |
| Mo | 99.97 | balance |
| Impurities | Max.values (μg/g) | Max.values (μg/g) |
| Al | 10 | - |
| Cu | 20 | - |
| Cr | 20 | - |
| Fe | 20 | 100 |
| K | 20 | - |
| Ni | 10 | 50 |
| Si | 20 | 100 |
| W | 300 | - |
| C | 30 | 100 |
| H | 10 | 20 |
| N | 10 | 70 |
| O | 40 | - |
| Cd | 5 | - |
| Hg | 1 | - |
| Pb | 5 | - |